-
十余年實力沉淀 專注流體設備主營
視覺點膠機
食品裱花機
視覺點鉆機
視覺點漆機
視覺點膠機
食品裱花機
視覺點鉆機
視覺點漆機
專業人士告訴你更換全自動點膠機膠管需要注意哪幾點！
點膠機膠管
在點膠機的使用中，必然要遇到更換點膠機膠管的情況。那么，更換膠管又有什么注意事項呢？下面柏銳就來教大家如何做。
In the use of the dispenser, it is inevitable to encounter the replacement of the rubber hose of the dispenser. So, what are the precautions for replacing the hose? Here, Bai Rui will teach you how to do it.
全自動視覺點膠機
首先要關閉點膠機，如果有冷卻套，要將它卸下來。然后再將氣壓頭、膠管撤下。膠管卸下來后，點膠閥接頭底部必然有空腔，可以用舊膠管來填充空腔。這時要看看轉接頭有沒有氣泡，如果有氣泡，則重新用新的膠管去填充。當氣泡不存在了，就可以加入膠水并將氣壓頭、冷卻套重新按上，隨后重啟點膠機設備檢測能否正常運作。
First turn off the dispenser. If there is a cooling jacket, remove it. Then remove the air head and hose. After the hose is removed, there must be a cavity at the bottom of the dispensing valve joint, and the old hose can be used to fill the cavity. At this time, look at the adapter for air bubbles. If there are air bubbles, refill with a new hose. When the bubble does not exist, you can add glue and press the air head and cooling jacket again, then restart the dispenser to check whether it works properly.
當點膠機在工作時，膠管材料卻用完了，這樣很容易讓點膠閥產生空氣。而且如果點膠機膠管內的膠體過了使用時間，那必須要將點膠閥跟點膠泵拆下來徹底清洗，然后在重新使用。
When the dispenser is in operation, the hose material is used up, which makes it easy for the dispensing valve to generate air. Moreover, if the gel in the dispenser hose has passed the use time, the dispensing valve and the dispensing pump must be removed and thoroughly cleaned, and then reused.
